Automatic aerosol filling machine is the production of aerosol machinery and equipment, aerosol is more common in life, common in life, sunscreen spray, medical spray, mosquito repellent, etc., are a kind of aerosol. Automatic aerosol filling machine is a filling equipment for the production of aerosol.
The automatic aerosol filling machine consists of three parts: filling machine, sealing machine and inflator. The equipment is powered by an air compressor and does not require electricity.
First, adjust the host air source pressure.
Open the front hand slide valve of the air source, pull up the pressure regulator knob on the air source, rotate clockwise, and the pressure rises. Rotate counterclockwise, pressure drops. Adjust to the required pressure (generally adjusted to 0.6-0.7MPa), press the pressure regulator to lock.
Second, adjust the sealing diameter and sealing depth
Open the host air supply front hand slide valve and the seal knob switch on the panel, take a valve and press it into the seal head with your finger, step on the foot valve, take out the valve, and measure the outside diameter and height of the seal. Generally, iron cans are equipped with iron valves, and the outer diameter of the seal is controlled at 27.9mm~28.0mm. The sealing height is controlled at 5.1mm-5.2mm. First loosen the lock nut on the sealing diameter adjusting block, turn the adjusting block counterclockwise to increase the sealing diameter, turn the adjusting block clockwise to reduce the sealing diameter. If the sealing height needs to be adjusted, then first loosen the three fastening screws under the sealing mouth with the hex. The right turn of the rotating block is to increase the sealing height, and the left turn is to reduce the sealing height. After adjusting the outer diameter and height of the desired seal, lock the nut tightly. (Note that when adjusting the sealing diameter, the sealing diameter has a value, after adjusting this value, the sealing diameter will no longer increase, and when sealing, the claw rod should not extend the sealing claw, so as not to crush the valve).
Three, adjust the height of the host board.
First press the top of the sealer to bring the sealing cylinder down to the bottom, then the bottom of the sealing cylinder will press the copper top pin on the sealing signal valve. Then place an aerosol tank to be filled in the guide rail directly below the sealing mouth (Note: The aerosol tank is already sealed for easy positioning). Loosen the positioning screws of the front guide column and the four fastening screws at the back of the column. Rotate the lifting crank to adjust the height of the platform, so that the sealing mouth just presses down the valve of the aerosol tank, and the sealing mouth should not be too tight or too loose when pressing the valve, so that the jar can just not move up and down. Then tighten the table guide post positioning screws and table post fastening screws.
Fourth, adjust the position of the liquid filling head and the inflating head.
Close the front hand slide valve of the main engine air source, place an aerosol tank under the sealing machine, press the top of the sealing machine with the hand, so that the sealing mouth presses the aerosol tank, keep the position of the aerosol tank stationary, and then place the aerosol tank in the guide rail, so that it is close to the aerosol tank under the sealing mouth. Loosen the four nuts fixed on the table plate of the filling head, adjust the position of the filling head so that the filling nozzle is facing the aerosol tank, and then tighten the nuts. Adjust the position of the inflation head in the same way, so that the inflation nozzle is directly opposite the spool position of the valve, and then tighten the nut. Then place an aerosol tank next to the aerosol tank under the inflator head, adjust the positioning handle at the end of the guide rail so that it is just against the aerosol tank, and tighten the nut.
Five, filling machine, inflator measurement adjustment.
The height of the metering cylinder positioning piston can be adjusted by rotating the adjusting handle on the top of the metering cylinder, so as to change the stroke of the metering cylinder piston to change the metering size of the filling. (Note that before adjustment, close the front hand slide valve of the air source on the main engine, and wait for the compressed air in the equipment to be emptied, otherwise the handle cannot be turned. Choose to adjust the metering from small to large (clockwise is to increase the metering), the adjustment process may occur after adjusting a distance after the handle can no longer continue to rotate, if the gas metering cylinder is adjusted, it is necessary to push the inflation nozzle of the inflation head upward, and appropriately discharge a little liquefied gas to continue to adjust; If the liquid metering cylinder is adjusted, it is necessary to use a small rod to push up the white tetrafluoroethylene plug in the liquid filling head, and be careful not to use too much force to avoid damage to the plug. Then use the container to catch the liquid flowing out when adjusting the measurement under the liquid filling head). First adjust the measurement to a general position, test filling, and then adjust the measurement according to the filling amount until the measurement meets the required requirements.
Six, the commissioning of booster pump.
Air before hand slide valve open the booster pump, booster pump at the idle running situation of piston motion, a "white" reversing the sound of the exhaust. By adjusting the pressure reducing valve adjustment knob on the booster pump air source triplet to adjust the pressure of the projectile, the general adjustment of the projectile pressure is 1.0MPa.
Nov 01, 2024
How To Adjust Automatic Aerosol Filling Machine?
Send Inquiry
